summaryrefslogtreecommitdiff
path: root/source/n/network-scripts/scripts/rc.inet1.conf
diff options
context:
space:
mode:
Diffstat (limited to 'source/n/network-scripts/scripts/rc.inet1.conf')
-rw-r--r--source/n/network-scripts/scripts/rc.inet1.conf107
1 files changed, 107 insertions, 0 deletions
diff --git a/source/n/network-scripts/scripts/rc.inet1.conf b/source/n/network-scripts/scripts/rc.inet1.conf
new file mode 100644
index 00000000..555210c4
--- /dev/null
+++ b/source/n/network-scripts/scripts/rc.inet1.conf
@@ -0,0 +1,107 @@
+# /etc/rc.d/rc.inet1.conf
+#
+# This file contains the configuration settings for network interfaces.
+# If USE_DHCP[interface] is set to "yes", this overrides any other settings.
+# If you don't have an interface, leave the settings null ("").
+
+# You can configure network interfaces other than eth0,eth1... by setting
+# IFNAME[interface] to the interface's name. If IFNAME[interface] is unset
+# or empty, it is assumed you're configuring eth<interface>.
+
+# Several other parameters are available, the end of this file contains a
+# comprehensive set of examples.
+
+# =============================================================================
+
+# Config information for eth0:
+IPADDR[0]=""
+NETMASK[0]=""
+USE_DHCP[0]=""
+DHCP_HOSTNAME[0]=""
+
+# Config information for eth1:
+IPADDR[1]=""
+NETMASK[1]=""
+USE_DHCP[1]=""
+DHCP_HOSTNAME[1]=""
+
+# Config information for eth2:
+IPADDR[2]=""
+NETMASK[2]=""
+USE_DHCP[2]=""
+DHCP_HOSTNAME[2]=""
+
+# Config information for eth3:
+IPADDR[3]=""
+NETMASK[3]=""
+USE_DHCP[3]=""
+DHCP_HOSTNAME[3]=""
+
+# Default gateway IP address:
+GATEWAY=""
+
+# Change this to "yes" for debugging output to stdout. Unfortunately,
+# /sbin/hotplug seems to disable stdout so you'll only see debugging output
+# when rc.inet1 is called directly.
+DEBUG_ETH_UP="no"
+
+## Example config information for wlan0. Uncomment the lines you need and fill
+## in your data. (You may not need all of these for your wireless network)
+#IFNAME[4]="wlan0"
+#IPADDR[4]=""
+#NETMASK[4]=""
+#USE_DHCP[4]="yes"
+#DHCP_HOSTNAME[4]="icculus-wireless"
+#DHCP_KEEPRESOLV[4]="yes"
+#DHCP_KEEPNTP[4]="yes"
+#DHCP_KEEPGW[4]="yes"
+#DHCP_IPADDR[4]=""
+#WLAN_ESSID[4]=DARKSTAR
+#WLAN_MODE[4]=Managed
+#WLAN_RATE[4]="54M auto"
+#WLAN_CHANNEL[4]="auto"
+#WLAN_KEY[4]="D5A31F54ACF0487C2D0B1C10D2"
+#WLAN_IWPRIV[4]="set AuthMode=WPAPSK | set EncrypType=TKIP | set WPAPSK=96389dc66eaf7e6efd5b5523ae43c7925ff4df2f8b7099495192d44a774fda16"
+#WLAN_WPA[4]="wpa_supplicant"
+#WLAN_WPADRIVER[4]="wext"
+#WLAN_WPAWAIT[4]=30
+
+## Some examples of additional network parameters that you can use.
+## Config information for wlan0:
+#IFNAME[4]="wlan0" # Use a different interface name instead of
+ # the default 'eth4'
+#IFNAME[4]="eth0:1" # Set up an IP alias.
+#HWADDR[4]="00:01:23:45:67:89" # Overrule the card's hardware MAC address
+#MTU[4]="" # The default MTU is 1500, but you might need
+ # 1360 when you use NAT'ed IPSec traffic.
+#DHCP_TIMEOUT[4]=15 # The default timeout for the DHCP client to
+ # wait for server resonse is 10 seconds, but
+ # you might want a shorter or longer wait.
+#DHCP_KEEPRESOLV[4]="yes" # If you dont want /etc/resolv.conf overwritten
+#DHCP_KEEPNTP[4]="yes" # If you don't want ntp.conf overwritten
+#DHCP_KEEPGW[4]="yes" # If you don't want the DHCP server to change
+ # your default gateway
+#DHCP_IPADDR[4]="" # Request a specific IP address from the DHCP
+ # server
+#DHCP_DEBUG[4]="yes" # Make dhcpcd show verbose diagnostics
+#DHCP_NOIPV4LL[4]="yes" # Do not assign an ipv4ll address when a DHCP
+ # server is not found (ipv4ll link-local
+ # adresses in the IP range 169.254.0.0/16 are
+ # also known as "zeroconf" addresses)
+#WLAN_ESSID[4]=DARKSTAR # An example of how you can override _any_
+ # parameter defined in rc.wireless.conf, by
+ # prepending 'WLAN_' to the parameter's name.
+ # Useful with multiple wireless interfaces.
+#WLAN_IWPRIV[4]="set AuthMode=WPAPSK | set EncrypType=TKIP | set WPAPSK=thekey"
+ # Some drivers require a private ioctl to be
+ # set through the iwpriv command. If more than
+ # one is required, you can place them in the
+ # IWPRIV parameter (separated with the pipe (|)
+ # character, see the example).
+#WLAN_WPA[4]="wpa_supplicant" # Run wpa_supplicant for WPA support
+#WLAN_WPADRIVER[4]="ndiswrapper"# Tell wpa_supplicant to specifically use the
+ # ndiswrapper driver (if you leave this empty
+ # the 'wext' driver is used by default)
+#WLAN_WPAWAIT[4]=30 # In case it takes long for the WPA association
+ # to finish, you can increase the wait time
+ # (defaults to 10 seconds)