summaryrefslogtreecommitdiff
path: root/source/a/mkinitrd/README.initrd
diff options
context:
space:
mode:
Diffstat (limited to 'source/a/mkinitrd/README.initrd')
-rw-r--r--source/a/mkinitrd/README.initrd24
1 files changed, 12 insertions, 12 deletions
diff --git a/source/a/mkinitrd/README.initrd b/source/a/mkinitrd/README.initrd
index 86d77539..ca95c332 100644
--- a/source/a/mkinitrd/README.initrd
+++ b/source/a/mkinitrd/README.initrd
@@ -1,7 +1,7 @@
Slackware initrd mini HOWTO
by Patrick Volkerding, volkerdi@slackware.com
-Wed Jun 17 01:49:18 CDT 2009
+Thu Apr 7 06:02:26 CDT 2011
This document describes how to create and install an initrd, which may be
required to use the 2.6 kernel. Also see "man mkinitrd".
@@ -22,7 +22,7 @@ and before the main root filesystem is mounted.
The usual reason to use an initrd is because you need to load kernel
modules before mounting the root partition. Usually these modules are
-required to support the filesystem used by the root partition (ext3, ext4,
+required to support the filesystem used by the root partition (ext3,
reiserfs, xfs), or perhaps the controller that the hard drive is attached
to (SCSI, RAID, etc). Essentially, there are so many different options
available in modern Linux kernels that it isn't practical to try to ship
@@ -33,15 +33,15 @@ flexible to ship a generic kernel and a set of kernel modules for it.
The easiest way to make the initrd is to use the mkinitrd script included
in Slackware's mkinitrd package. We'll walk through the process of
-upgrading to the generic 2.6.29.5 Linux kernel using the packages
+upgrading to the generic 2.6.37.6 Linux kernel using the packages
found in Slackware's slackware/a/ directory.
First, make sure the kernel, kernel modules, and mkinitrd package are
installed (the current version numbers might be a little different, so
this is just an example):
- installpkg kernel-generic-2.6.29.5-i686-1.tgz
- installpkg kernel-modules-2.6.29.5-i686-1.tgz
+ installpkg kernel-generic-2.6.37.6-i686-1.tgz
+ installpkg kernel-modules-2.6.37.6-i686-1.tgz
installpkg mkinitrd-1.1.0-i486-1.tgz
Change into the /boot directory:
@@ -52,7 +52,7 @@ Now you'll want to run "mkinitrd". I'm using reiserfs for my root
filesystem, and since it's an IDE system the reiserfs module will be
the only one I need to load:
- mkinitrd -c -k 2.6.32.3 -m reiserfs
+ mkinitrd -c -k 2.6.37.6 -m reiserfs
This should do two things. First, it will create a directory
/boot/initrd-tree containing the initrd's filesystem. Then it will
@@ -61,10 +61,10 @@ you could make some additional changes in /boot/initrd-tree/ and
then run mkinitrd again without options to rebuild the image. That's
optional, though, and only advanced users will need to think about that.
-Here's another example: Build an initrd image using Linux 2.6.32.3
-kernel modules for a system with an ext4 root partition on /dev/sdb3:
+Here's another example: Build an initrd image using Linux 2.6.37.6
+kernel modules for a system with an ext3 root partition on /dev/sdb3:
- mkinitrd -c -k 2.6.32.3 -m ext4 -f ext4 -r /dev/sdb3
+ mkinitrd -c -k 2.6.37.6 -m ext3 -f ext3 -r /dev/sdb3
4. Now that I've built an initrd, how do I use it?
@@ -76,10 +76,10 @@ initrd. Here's an example section of lilo.conf showing how this is
done:
# Linux bootable partition config begins
-image = /boot/vmlinuz-generic-2.6.32.3
+image = /boot/vmlinuz-generic-2.6.37.6
initrd = /boot/initrd.gz
- root = /dev/sdb3
- label = Lnx26323
+ root = /dev/sda6
+ label = Lnx26376
read-only
# Linux bootable partition config ends